Support

Support Options

Submit a Support Ticket

 

Tags: tool:cntfet

All Categories (1-14 of 14)

  1. Can you please tell me the working of CNTFET. It seems a bit confusing to me. what type of cntfet do you use? SB or gate doped?

    Closed | Responses: 0

    http://nanohub.org/answers/question/1078

  2. Where, why, and how you used Dyson equation

    Open | Responses: 1

    It’s mentioned that Dyson equation is used. Would you please let me know in which part you used Dyson equation. Which part of Hamiltonian considered as perturbation and why? I...

    http://nanohub.org/answers/question/902

  3. Why the effect of temperature is different at on and off-state current?

    Open | Responses: 1

    For V(drain)=0.1V or 0.4V and V(gate)=0V, by increasing the temperature (300ºk, 400ºk, 500ºk) the current (off-state current) increases. Such behavior can be seen for V(drain)=0.4V and...

    http://nanohub.org/answers/question/872

  4. why the saturation current increases with decrease in diameter of the CNT

    Closed | Responses: 3

    I had done the simulation using your tool “CNTFET Lab” available at nanohub. I have done the simulations for different diameter of the CNT (by changing the chirality) used in the channel. The...

    http://nanohub.org/answers/question/866

  5. is there a problem with the simulator?

    Closed | Responses: 1

    hi, I tried to get some I-V curves but I couldnt (even with default settings)I just get values of drain source or gate voltage and there is not any curve, just the values..

    http://nanohub.org/answers/question/459

  6. what is the threshold voltage

    Closed | Responses: 3

    for simulation of CNTFET what is the exact value of the threshold voltage? how does this depends on the device parameters.

    http://nanohub.org/answers/question/450

  7. How long did users took to run a simulation for CNTFET? It took me like1 hr to run a simulation. Is this normal?

    Closed | Responses: 2

    http://nanohub.org/answers/question/416

  8. why I~vds curve shows higher saturation current for longer channel length?

    Open | Responses: 1

    I was simulating for CNTFETs with different channel length.I had taken a (10,0) CNT.I tried to plot I~vds curve for channel lengths 10nm,15nm and 30nm.saturation current for 10nm is coming...

    http://nanohub.org/answers/question/200

  9. What is the Diameter of the nanotube in this simulation?

    Open | Responses: 1

    What is the Diameter of the nanotube in this simulation? I can not find the value in the parameters-setting part.

    http://nanohub.org/answers/question/167

  10. i can’t find output in simulation of cntfet

    Open | Responses: 2

    hi sir , i can’t find output in simulation of cntfet, i want to have IV curves in result of simulation , plz help me.

    http://nanohub.org/answers/question/20

  11. CNTFET Lab

    13 Mar 2006 | Tools | Contributor(s): Neophytos Neophytou, Shaikh S. Ahmed, Eric Polizzi, Gerhard Klimeck, Mark Lundstrom

    Simulates ballistic transport properties in 3D Carbon NanoTube Field Effect Transistor (CNTFET) devices

    http://nanohub.org/resources/cntfet

  12. Shaikh S. Ahmed

    Shaikh Shahid Ahmed received the B.S. degree in electrical and electronic engineering from Bangladesh University of Engineering and Technology (BUET), Dhaka, Bangladesh, in...

    http://nanohub.org/members/9293

  13. Neophytos Neophytou

    Neophytos Neophytou is a postdoctoral research scientist at the Technical University of Vienna since August 2008. Neophytos Neophytou received his B. S. degree in Electrical and Computer...

    http://nanohub.org/members/3698

nanoHUB.org, a resource for nanoscience and nanotechnology, is supported by the National Science Foundation and other funding agencies. Any opinions, findings, and conclusions or recommendations expressed in this material are those of the author(s) and do not necessarily reflect the views of the National Science Foundation.