
NanoMOS 3.5 (online Verison)
Open  Responses: 1
When I used NanoMOS 3.5 on nanoHub, I got the same answers when I set Ambient Temperature at 200 & 300 K...
http://nanohub.org/answers/question/326

About voltage stepping
Closed  Responses: 0
Hello,
First of all, thanks a lot for this amazing tool, but I am wondering why I can not get proper voltage shift for drain voltagecurrent graph. I gave drain voltage step as 0.1, gate...
http://nanohub.org/answers/question/388

Can it simulate quasi ballistic transport
Closed  Responses: 1
Can NanoMOS3.5.4 simulate quasi ballistic transport? Is there any tool to simulate quasi ballistic transport...
http://nanohub.org/answers/question/412

Can nanoMOS simulate a tunneling transistor?
Open  Responses: 2
I’m wondering if nanoMOS can simulate a tunneling transistor. It’s a gated pin diode.
http://nanohub.org/answers/question/1056

coefficient’s in si/oxid interface in poisson.m
Closed  Responses: 0
what's the coefficient's 1/8 or 3/8 in si/oxid interface in poisson.m file?
there aren't this coefficients in (3.2b) equation in ren thesis!
http://nanohub.org/answers/question/204

double gate mosfet width (W) in nanoMos
Open  Responses: 2
http://nanohub.org/answers/question/206

eps_c and eps_si definition
Closed  Responses: 0
I am trying to simulate a doublegate MOSFET with a new material. However, I am not clear about the what eps_c and eps_si are respectively. From my understanding, eps_si is the dielectric...
http://nanohub.org/answers/question/1194

Error regarding path
Open  Responses: 1
Hi
I get the following error when I try to run Nanomos.
{b??? Error using ==> load
Unable to read...
http://nanohub.org/answers/question/848

for the same case, the simulation results by the newest version are not the same as those simulated by the previous versions, any parameter changed?
Closed  Responses: 0
http://nanohub.org/answers/question/965

How can I retreve the stored data obtained from previous simualtions and plot them again?
Closed  Responses: 1
http://nanohub.org/answers/question/174

How do I derive the 2D electron density used in nano MOSFET calculations?
Open  Responses: 1
In nanomos2.5, the density of charge is obtained by multiplying the square of the wavefunction by a prefactor: with semiclassical method, that prefactor is given by
http://nanohub.org/answers/question/54

How the Fermi level (EF) is determined for charge and current calculation?
Closed  Responses: 0
http://nanohub.org/answers/question/721

how to model driftdiffusion transport
Closed  Responses: 0
Which way is for simulating driftdiffusion transport? Can the driftdiffusion tansport model simulate quasi ballistic transport? What is the mobility's unit?
http://nanohub.org/answers/question/411

Is version 4.0 source code available?
Closed  Responses: 0
I was wondering if the version 4.0 source code is available for download?
http://nanohub.org/answers/question/1126

junction abruptness and quantization questions
Open  Responses: 4
When setting up the device structure in nanoMOS, the program asks for the source/drain gaussian profile abruptness in units of dec/nm. There are two problems here. First, there’s a...
http://nanohub.org/answers/question/101

matlab version
Closed  Responses: 1
I am running nanomos 2.5 and I am getting different results when using matlab version 6.5 or 7.0 then when using the online version or running matlab 6.1. Is this a known issue? Currents are...
http://nanohub.org/answers/question/173

Models
Closed  Responses: 0
How can I run for examples 3a and 3b a simulation using Classical Ballistic Model? And a Energy Balance Model?
In the window appearing I can choose the DriftDiffusion Model and two other...
http://nanohub.org/answers/question/368

nanoMOS always reports error
Closed  Responses: 1
I am sure I followed the instructions strictly as followed:
‘The Matlab version
=====================
nanoMOS is written in Matlab a scripting language (http://nanohub.org/answers/question/443

nanomos key command
Open  Responses: 1
I downloaded nanamos program in my PC. I am not familiar with MATLAB. kindly would you please explain me the different steps to run this program from my PC.
http://nanohub.org/answers/question/102

Problem launching job: 0child process exited abnormally
Closed  Responses: 0
Hi,
Even though I was using the default settings, NanoMOS with TRANSPORT MODEL “NEGF with phonon...
http://nanohub.org/answers/question/1004